The three lip products, and what each one is for
The lip is not one tool. The rail splits it into two paints and a shine, and they sit next to each other in the left column, so you scroll once instead of hunting.
| Product | Where it sits | What it does | Use it when |
|---|---|---|---|
Lip Liner |
Left rail, immediately above Lipstick in the recording read for this page |
Draws the border, so the fill has an edge to stop at | You want a defined mouth, an overline, or a smaller lip than the one under it |
Lipstick |
Left rail, immediately below Lip Liner |
Fills the inside with colour, and it is the first lip tool the recorded session reached for | You are blocking the lip in the first minute of a round |
Clear Lip Gloss |
Lower in the same rail, past Glitter in the order read from a phone session |
Adds shine without changing the colour underneath | You want the middle to catch the light and the colour left as it is |
All three open the same scrollable panel on the right, and the swatch block is headed LIP COLOURS instead of COLOUR. Under that heading sit three palettes — Classic, Neon VIP and Metallic VIP — then Custom colour + for the wheel and My Saved Palette + for shades you kept. Whether the two VIP palettes open on an account without the VIP pass was not tested here, so press the tab in your own session before you build a look around one of them.
The order: fill first, shine second, border last
The intuitive order is liner, then fill. The recording this page read does the opposite, and the reversed order is the reason it survives a countdown: if the border goes on last, you never have to keep a brush inside a line you already drew. The line cuts the fill back to the shape you want.
- Fill the whole lip with
Lipstick. Pick a mid shade and cover the lip inside its own border, corners included. At 00:10 of the recordingLipstickwas the lit entry on the rail and the mouth was already covered in one pink. - Put the shine in before the line, on its own layer. The panel reads
LAYERS · 3 / 4at 00:48 withLayer 2ticked, and its own note says Blend and Wipe act on the selected layer only. Three layers were in use at that point, and the passes this recording shows are the fill, the shine and the border. Wipe a shine you dislike on its own layer and the fill survives. - Paint the bright patch into the middle of the lower lip. In the recording the circled swatch at 00:30 is a pale dusty pink, several steps lighter than the fill, and the bright area sits in the centre of the lower lip. The tool column is off screen across that stretch, so which product painted it is not readable in these frames; a light
Lipstickshade andClear Lip Glossboth land in the same place. Keep it in the middle: run that colour to both corners and the mouth reads wet rather than glossy. - Cut the border with
Lip Liner. At 00:34 the lit entry moves toLip Liner, at 00:36 the circled swatch is a dark brown, and from 00:37 the brush runs along the lip edge. Two or three swatches darker than the fill is what keeps the shape readable at runway distance. - Soften only what needs softening. A border that looks drawn on is a strength problem, not a colour problem: take the Blender from the bottom bar and press along the edge, and it softens the selected layer rather than the whole face. The sizes one recorded session used for that pass are on the blending guide.
- Clean the outside with concealer. The creator of this recording puts that step in her own comment under the video: once the combo is done, trace around it with a concealer that matches the skin tone, which sharpens the shape and hides the spills. It is one creator's method, and this page has not tested how that pass behaves on its own layer.
- Check it at full-face distance. The
Toggle Zoombutton in the bottom bar goes back out. A mouth that looks right at close range and small at talking distance is usually a border that is too thin, not a fill that is too pale.
What one recorded session had the panel set to
These are readings from single frames of one upload, not a prescription. Copy the shape of the settings, not the numbers.
| Reading | Value at that frame | What it tells you |
|---|---|---|
| Layers | LAYERS · 3 / 4, Layer 2 ticked, Add layer below |
Three passes were kept apart, and the panel holds four layers in total |
| Brush size | BRUSH SIZE slider at 2 (00:48) |
The low end of the slider, which is where edge work belongs |
| Strength | STRENGTH 81% (00:48) |
High strength solidifies colour; drop it for a soft edge or a blended shine |
| Palette heading | LIP COLOURS under Colour Picker |
The lip palettes are their own set, not the full face palette |
The tool column is off screen in the frame that carries the size and strength readings, so those two numbers belong to that session rather than to a named step. The recording never shows its slider during the fill or the shine either, so no step-by-step value is claimed here for those passes.
Five things that go wrong, and the fix for each
| What you see | Why | Fix |
|---|---|---|
| The mouth looks smaller than the model's own lips | The border was drawn inside the lip line | Wipe that layer and redraw the border on the edge, or just outside it for an overline |
| The whole lip glows instead of the middle | The light colour was run corner to corner | Wipe the shine layer and rebuild it as one patch in the centre of the lower lip |
| Wipe erased the fill as well as the mistake | Both passes sat on the same layer | Use Add layer before the shine and before the border, so Wipe only reaches the pass you are on |
| The shade reads grey or washed out under the stage light | A muted swatch with high strength and nothing to contrast against | Add the darker border and put the mirror-mode check on the whole face before the timer runs out |
| The border is only half drawn when the clock ends | The line was begun at a corner instead of at the cupid's bow | Start at the centre of the top lip and work outwards, so an interrupted line still closes the shape |
Practising it before the round counts
The lip work in the recording runs through three products and three layers. That is more passes than a timed round rewards if you have never done it, so build the mouth in Freeplay first, where nothing is scored. Do it twice: once fast, covering the lip and cutting the border, and once slow with the shine, and keep the one you can repeat under a clock.
A finished face can also be kept instead of rebuilt. Saved Looks stores complete looks in three slots, so a combo you are happy with is one load away on the next round; the saved-looks page covers what a slot holds and what it costs.
What this page does not claim
- Which product painted the shine. The bright patch is on screen at 00:24-00:32, but the tool column is off screen across that stretch, so neither
LipsticknorClear Lip Glosscan be named for it. The gloss is a separate entry lower down the rail; no gloss pass was read here. - That the VIP palettes are free.
Neon VIPandMetallic VIPare visible tabs; whether they open without the pass was not tested. - That a lip combo changes the score. The vote is read in the runway guide, and nothing read here connects a lip style to a star rating.
- That these readings are current. The frames come from an upload dated 11 October 2026, and the newest build this site has read is 25 October 2026. This game renames tools between builds, so read your own rail before following a name.
- Exact numbers for the fill and the shine. No frame read here shows the size or strength slider during those two passes.